Sewing a body pillow

The other “Home Improvements” project I finished last week was a body pillow for our bedroom. I created it to fit into our plan for a cohesive style. I decided to use two fabrics to give it a little extra, and I’m very happy with the result. Though I made a few (fixable) mistakes as I went, it’s one of the few finished products I’ve been able to call perfect.

Body Pillow

Special considerations:

  • Color: I chose silver and grey to fit into our overall palette while contrasting each other enough to express the difference between materials
  • Material: Silk and velvet fit the feel of the room, but they are slightly more difficult to work with. I used a smaller sewing needle and lots of pins.
  • Zipper: Since I want the pillow to last, I included a zipper in the design – this way I can change out the stuffing if it starts to lump, and remove it for cleaning.

Cutting FabricSewing Silk

1. Measure and cut fabric. I used the full width of my velvet, then added enough silk on each end to make it the width of our bed (adding seam allowances).

2. Pin and sew end pieces to middle. I made each silk end piece exactly the same size, then pinned them to the ends of the velvet (right sides facing) and sewed together.

Layout fabricAlign fabric

3. Line up all pieces and trim. I first made this as one large rectangle, then cut it in half (to make the 2 sides) and trimmed each to match up.

4. Pin together. Make sure all your seams are aligned!

Pin ZipperTurn

5. Add the zipper (optional). Design Sponge has a great tutorial here. Put it in a place it won’t be noticed – mine is along the bottom (but not the whole length). Don’t forget to unzip it when you’re done, or turning will be a pain!

6. Pin and sew around. Remember to back-tack! (If you don’t add a zipper, you’d better leave an opening to turn.) Go ahead and trim any bulky seams and clip corners, too.

7. Turn right side out, stuff, zip. (No zipper people: sew the gap closed.) You’re done!

Quick & Easy Cushion Tutorial

Chase on his new dog bed

I made mine to be a dog bed for Chase, but this could also be a floor pillow, a bench cushion, or a million other things – the possibilities are endless!

Supplies:

  • Large pillow case (or fabric, folded) [Mine was $2 on clearance at Ikea!]
  • Fabric scraps and/or stuffing
  • Sewing machine, pins, thread, scissors

Now for the instructions!

Cut seams2 squares and 2 stripsSew strips togetherPin sides to square

  1. Cut your pillow case in half to form a square from the closed end (or cut 2 squares from your fabric). Turn inside out; remove side seams and cut fold so you have 2 squares.
  2. From remaining pillow case (or fabric), cut 2 strips along the cut edge – the width will be the depth of your cushion.
  3. Cut one side seam off each piece, so that they are strips instead of circles (each should now be the length of 2 sides of your square – the seam in the middle will be a corner).
  4. Pin the 2 strips right sides together. Sew each end. You now have the 4 sides of your cushion, forming a square.
  5. Pin the sides to one square of fabric, right sides together. Sew around.
  6. Now pin the second square to the open sides. Sew, leaving a 4in. gap.
  7. Turn and stuff! [I used fabric scraps I’ve been saving forever!] Sew gap closed.
  8. Place in a cozy place and add sleepy dog (Optional ;))

Sew, right sides togetherLeave 4" gap for turningStuff with fabric scrapsscrap-eating monster! nom nom

I tried to make this really simple, so I hope it makes sense for everyone. Please don’t hesitate to leave a comment if you have any questions! Now go make and enjoy your quick & easy cushions 😀

Sleepy dog on his new dog bed